Just How to Install a Bathtub Yourself
Just How to Install a Bathtub Yourself
Blog Article
Just about every person has their own individual piece of advice with regards to How to Install a Bathtub Yourself.
Installing a bathtub isn't precisely rocket science, but it does require solid plumbing, carpentry, and sometimes, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably tough job. If the old bathtub is easily available, the project can relocate easily; if you need to open up a wall surface to eliminate the old tub and position the brand-new bath tub, the job is much harder. In either case, the project is within a home handyman's abilities, although you will certainly require a helper to move out the old bathtub as well as set in the new one. Ensure you have qualified yourself for the job and fit trying it. As opposed to working with a specialist to take over a halfway-completed project, it is far better to take into consideration utilizing one before you start. Possibilities are you may need a specialist plumber to make tube links.
This short article will help you mount a brand-new tub in your bathroom if you have actually currently bought a brand-new bathtub and do not need to change the arrangement of your previous water system pipelines.
Your tools and also product checklist ought to make up the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the water system. After doing so, turn on the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be rather problematic as a result of the limited access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single faucets from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washing machines remain in area between the tap as well as the sink. Protect the faucet in position with the manufacturer offered backnut. When the faucet is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical tap ports. The previous kind needs to be attached to the faucet finishes first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Tub
Utilizing the two wooden boards under its feet, put the tub in the needed setting. The wooden boards are valuable in uniformly spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
The next goal is to ensure that the bathtub is leveled all round. This can be attained by examining the level and also readjusting the feet on the tub up until the spirit level reads level.
To install faucets, fit all-time low of the outermost versatile tap adapter to the proper supply pipeline by making a compression join; then do the very same for the various other faucet.
Turn on the supply of water as well as check all joints and brand-new pipework for leakages and tighten them if essential. Load the bath tub as well as likewise check the overflow outlet and also the typical outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bathtub needs to wait up until the bathtub has been made use of a minimum of once as this will certainly resolve it into its final position.
Preparing for the Installment
To start with, the sustaining framework supplied with the bathroom needs to be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of the two taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last position.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, causing complications with wetness and also possible leakages to the ceiling below.
You can select from a variety of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, as well as are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the tub with water prior to sealing, to enable the movement experienced when the tub remains in use. The sealant can split fairly early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently available on the market. It is suggested to fit the tiles utilizing waterproof or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading about How to Install a Bathtub Yourself? Create feedback below. We will be delighted to hear your insights about this write-up. We are looking forward to see you back again later on. Appreciated our post? Please share it. Let someone else find it. We truly appreciate reading our article about How to Install a Bathtub Yourself.
This Resource
Report this page